AN54LQ-DB-15

AN54LQ-DB-15 demo board is designed for quick testing and debugging without building your own board. The board is available with AN54LQ-15 (Chip Antenna), AN54LQ-P15(PCB Antenna), and AN54LQ-U15(u.FL Connector) modules. 

Raytac's nRF54L15 module spectrum covers:
AN54LQ-15, AN54LQ-P15 and AN54LQ-U15 with Chip Antenna, PCB Antenna and u.FL connector for External Antenna
AN54LV-15, AN54LV-P15, AN54LV-U15 and AN54LV-K15 with Chip Antenna, PCB Antenna, u.FL connector for External Antenna, and Antenna Pin
Options for selection. 

Highlight of nRF54L15 Solution
* Supports BT6.0
* Supports Channel Sounding feature
* Excellent power saving performance





 

Raytac's AN54LQ-15 is a BT6.0 stack (Bluetooth low energy or BLE) module designed based on Nordic nRF54L15 SoC solution, which incorporates: GPIO, QSPI, SPI, UART, I2C, I2S, PDM, PWM, ADC and NFC interfaces for connecting peripherals and sensors.

Features
Dual Transmission mode of BLE & 2.4GHz RF upon customer's preference.
Compact size with (L) 13.7 x (W) 9.5 x (H) 1.8mm
Low power requirements, ultra-low peak, average and idle mode power consumption.
Supports Bluetooth 6.0, IEEE 802.15.4 & 2.4Ghz RF & ANT & upon customer's preference.
Pre-Certified Module: FCC / IC / CE / Telec / KC / SRRC / NCC / WPC Certified & CE RED / RCM Compliant.
Highly flexible multiprotocol SoC ideally suited for Bluetooth® Low Energy and 2.4GHz ultra-low-power wireless applications.
Quick Specifications
128 MHz ARM® Cortex™ processor with TrustZone® technology
Supply: 1.7V – 3.6V
Flexible and configurable 31 GPIOs
Bluetooth 6.0, IEEE 802.15.4-2020, and 2.4 GHz transceiver
    •  -96dBm sensitivity in 1Mbps Bluetooth low energy (BLE) mode
    •  -104 dBm sensitivity in 125 kbps Bluetooth Low Energy mode (long range) with a 0.1% bit error rate
    •  -102 dBm typical sensitivity in IEEE 802.15.4
    •  Up to +8 dBm TX power; 1 dB step size from -8 dBm to +8 dBm
    •  RSSI (1dB resolution)
Supported data rates:
•  Bluetooth 6.0: 2Mbps, 1 Mbps, 500 kbps, 125 kbps
•  IEEE 802.15.4-2020: 250 kbps
•  Proprietary 2.4 GHz: 4 Mbps, 2 Mbps, 1 Mbps
•  Advanced on-chip interfaces        
    •  RISC-V Coprocessor
    •  Global RTC (GRTC) that can run in System OFF mode and implement a shared system timer
    •  Seven 32-bit timers with counter mode
    •  Up to five fully featured serial interfaces with EasyDMA, supporting I2C, SPI controller/peripheral, and UART
    •  One high-speed SPIM up to 32 MHz, four up to 8 MHz
    •  One high-speed UARTE up to 4 Mbps, four up to 1 Mbps
    •  I2C up to 400 kHz
    •  Three pulse width modulator (PWM) units with EasyDMA
    •  I2S two channel Inter-IC sound interface
    •  ADC with up to eight programmable gain channels. 14-bit at 31.25 ksps,
12-bit at 250 ksps, and up to 10-bit at 2 Msps
    •  Pulse density modulation (PDM) interface
    •  Near field communication (NFC)
    •  Up to two quadrature decoders (QDEC)
    •  Comparator and low-power comparator with wake-up from System OFF mode
    •  Temperature sensor
Operating Temp: -40°C to +105°C
Platform security
    •  Secure/non-secure memory protection
    •  Symmetric and asymmetric key crypto accelerator
    •  ecure key management
    •  Tamper detection
    •  Immutable boot partition
    •  Debug access port protection
    •  Two watchdog timers for secure and non-secure access

Specification：                                                                                    
[nRF54L15_10_05] AN54LQ-15_AN54LQ-10_AN54LQ-05 Spec (Ver.1.1)

Design Guide includes
AN54LQ-15 & AN54LQ-P15 & AN54LQ-U15 Footprint & Design Guide (250919)

• Footprint (compatible for Protel, Altium Design)
• 2D/3D drawing
• Reflow/Solder Profile

RoHS & REACH Report：
RoHS & REACH Report for AN54LQ-15 & AN54LQ-P15 & AN54LQ-U15

Related Links：
•   Nordic 3rd Party Modules/Modems
(Raytac's modules are all qualified Nordic 3rd Party Bluetooth low energy module, please go following website for more detailed information.)